how To Inject Testosterone
Step 1: Gather Your Materials
First, you should get your materials together. You will need:
- Your testosterone prescription vial
- Fresh alcohol wipes
- A new syringe
- A new drawing needle
- A new injection needle
- A Sharps container to safely throw away your injection materials
Step 2: Clean and Sanitize
Before injecting the testosterone, wash your hands thoroughly for at least 20 seconds with soap and water. You should also use an alcohol wipe to sanitize the top of the testosterone bottle. Make sure to use a new drawing needle, new injection needle, and new alcohol wipes each time.
Step 3: Draw Your Testosterone to the Correct Dose
Unwrap your syringe from the packaging and attach the drawing needle to the syringe. Make sure you don’t touch the needle or the syringe to anything else – this helps avoid contamination.
Pull the syringe down to the appropriate dosage. Then pierce the rubber ring of your testosterone prescription vial with the drawing needle. Press the plunger of the syringe to push the air into the testosterone vial.
Invert the vial (hold it upside down) and pull the testosterone into the syringe to the appropriate dosage. Remove the needle from the vial.
Step 4: Switch From the Drawing Needle to the Injection Needle
Recap the drawing needle. Then remove the drawing needle from the syringe and replace it with the injection needle. The injection needle should be new and in its protective packaging.
Once again, do not allow the syringe or the needle to touch anything in order to avoid contamination.
Step 5: Remove Air From the Syringe
To release any air from the syringe, gently tap the syringe with your finger and then slowly press the plunger. Continue doing this carefully until there is only testosterone within the syringe.
Step 6: Inject the Testosterone
Before you inject, use an alcohol wipe to clean the injection site on your body. Rub the alcohol wipe in a circular motion outward from the injection site to ensure the area is clean.
Your testosterone injection may be intramuscular or subcutaneous depending on your unique protocol. Continue reading to learn more about these types of injections and to get specific instructions for each.
If you are doing an intramuscular injection into the deltoid (a common injection site), feel for the acromion, or the bony point of the shoulder. Move two finger-widths down from the acromion to find your injection spot. Hold the needle at a 90-degree angle, pierce the skin, and carefully inject the medicine.
Step 7: Discard the Needle and Syringe
Throw away the needle and syringe into a sharps container. If you do not have a sharps container, Opteluxe patients can order one through us or on Amazon.
Dispose of all medical waste appropriately. If you’re not sure how, you can contact your Primary Care physician or local pharmacy to learn your state’s requirements for disposing of needles and syringes.
Subcutaneous Injections and Intramuscular Injections
Subcutaneous injections, sometimes called subq injections or SQ injections, are injected into the fatty layer between the muscle and the skin. This type of injection is typically used for a smaller volume of medication, usually up to 2 mL.
With subq injections, the medication is absorbed by the body over a period of time. The injection is often more comfortable with less injection site pain, making it preferable for some testosterone replacement therapy patients.
Subcutaneous injections also allow for more frequent injections if necessary, which can help patients maintain testosterone levels effectively.
Intramuscular injections, or IM injections, are injected into the muscle at various points throughout the body.
Intramuscular injections can be uncomfortable and require a larger needle than SQ injections, and these injections are typically done once to twice a week.
Subcutaneous Injection Instructions
With Sub Q injections, you’ll need to pinch the skin between your thumb and forefinger in the area where you inject. If you can pinch about two inches of skin, you can inject by holding the needle at a 90-degree angle. If you can only pinch one inch of skin, you can inject by holding the needle at a 45-degree angle.
Subcutaneous injections can be injected into the following areas:
- The upper arm – Stand with your arm down and your hand at your hip, and gently pinch the skin midway down and at the back of the upper arm.
- The abdomen – Injection sites in the abdomen can be found at the natural line of the waist, where there is typically 1-2 inches of skin to pinch. The area around the belly button is typically a good spot for subq injections.
- The thigh – The middle of the thigh toward the outer side of the thigh is often an appropriate spot to inject.
- The glute – divide the buttock into four quarters, and inject into the upper right (right cheek) or upper left (left cheek) quarter.
How to do a Subcutaneous Injection
When you’re ready to begin, follow Steps One Through Five in the How to Inject Testosterone section to prepare your testosterone injection. Then choose your injection site. Many patients rotate through injection sites to avoid fatigue and over-injection in one area of the body.
Pinch the skin at your injection site between your thumb and forefinger. If you can pinch at least two inches of skin, hold the needle at a 90-degree angle; if you can only pinch one inch, then hold the needle at a 45-degree angle.
You should hold the needle with your dominant hand to ensure greater mobility. To grip the needle, hold the syringe with your thumb and first finger the way you would hold a pen.
Use your wrist to press the needle into the skin. Depending on how thick your skin is, it may require a little pressure. Do not forcefully shove the needle in, since this could cause bruising and potentially push the needle too deep.
Slowly depress the plunger of the syringe to inject the medication, then remove the needle at the same angle you used to push it into your skin. Dispose of the needle and syringe safely as listed above in Step Seven.
Intramuscular Injection Instructions
For IM injections, follow the preliminary steps from the How to Inject Testosterone section above. Once you reach Step Six, you will likely need to inject in one of the following IM injection sites:
- Vastus Lateralis Muscle – the top of the thigh. If you place your thumb at the top of your thigh and wrap your fingers around the side, you will feel this muscle.
- Deltoid Muscle – the shoulder. This injection site can be useful because injections can be performed standing or sitting down. Feel for the top of the shoulder, where the bone is, and imagine an upside-down triangle from that spot. Inject at the top of the triangle, about two fingers down from the shoulder point.
- Ventrogluteal muscle – the muscle of the hip. This muscle is a good injection site because it’s unlikely that you will hit blood vessels or nerves. However, it may require some help, since it’s on the backside of the body. To find this muscle, place your thumb on the base of your tailbone and move straight across either to the left or right. Then place your index finger two inches below your hip bone.
Once you have cleaned the area as instructed in Step Six from the How to Inject Testosterone section, you’ll want to let the area dry completely. Then pull the skin taut and hold it like that with your free hand.
Use your wrist to push the needle into the skin at a 90-degree angle. You don’t want to be too forceful, which can cause bruising, but you also don’t want to move too slowly. It should be quick but gentle. The needle is sharp enough to slide easily into your skin.
If you experience bleeding, you have likely hit a blood vessel and should dispose of the needle and medication and start over.
If you don’t experience any bleeding, depress the plunger steadily. Do not force the medication in too hard; this can cause discomfort. You may experience some stinging as you inject.
Once the medication has been injected, remove the needle quickly and dispose of appropriately as outlined in Step Seven above.